aluminumhm

An  anodized aluminium baking sheet  is an aluminum sheet made especially for baking, represented by 3003, 5005 and 5052 alloys, among which 3003 is the most popular. An anodized sheet differs from regular aluminium sheets in stronger hardness, corrosion resistance and insulation. Anodizing is to take aluminum alloy as anode and form oxide film on its surface by electrolysis. After surface anodizing, a sheet’s corrosion resistance, hardness, wear resistance, insulation, heat resistance, sanitation can be greatly improved. The melting point of hard anodized film reaches 2320k, but common anodized film only 100 degree centigrade. Thus actual performances of an anodized aluminum baking sheet has a lot to do with oxidation conditions, film thickness and sealing conditions. At present, baking dies are mainly made of aluminum alloy and carbon steel. Carbon steel is carbon iron alloy, which has the advantages of high hardness, easy smelting and low price.  Anodized aluminum...

Aluminum coil 5052 h34  is of 2.72g/cm3 and 0.2mm to 8mm thick. As a typical aluminum magnesium alloy, it contains a small amount of manganese, chromium, beryllium, titanium, etc. Although a small amount of manganese dissolves, most of it forms mnal6. The effect of chromium in 5052 aluminium is similar to that of manganese: to improve the ability of stress corrosion cracking resistance, increase the strength of base metal and weld, and reduce the tendency of welding cracks, but the content of chromium is generally less than 0.35%. With an elongation larger than 80,  5052 aluminum coil  is applied to aluminium checker plates, umbrella ribs, vehicle panels, plan oil tanks, ship sheet metal parts and so on. General properties of 5052 h34 aluminum coil incorporates good corrosion resistance, excellent welding property, satisfying cold processing ability, medium hardness, high fatigue resistance, and poor machining ability. In detail, properties of the coil fall on thre...

　　 7075 aluminum plate prices  are closely related to temper of the plate. 7075 6t, for example, proves to be cheaper than 7075 t651, although the former boasts higher hardness owing to smaller carbon content. In addition, thickness of a 7075 aluminum plate impacts its price, too. In China the price including tax for zero cutting of national standard  7075T6 aluminum plate   with thickness more than 10mm is about 33.8 yuan / kg, and the purchase price of the whole board is about 27 yuan / kg. The production cost of 7075 aluminum plate below 10 mm is higher, thus the price is higher. More importantly, the price also depends on the quantity and specification you need. 7075t6-aluminum plate-price-application 　　16 to 200mm thick, 7075 t6 aluminum plate mainly contains the alloy element of zinc, featured by strong strength, good mechanical properties and anode reaction. Fine grains endow it with good deep drilling performance, especially suitable for thread rolling. It is m...

　　 8021 aluminum foil manufacturers   supply 8021 foil of thickness from 0.015mm to 0.2mm and width between 100mm and 1650mm. Covering tempers of F, O, H14, H16, H18, H19, H22, H24, H26 and H28, the foil is mainly applied to battery soft packaging, food containers and food packaging. 　　8021  aluminum foil  from leading manufacturers like Haomei features good deep drawing property, tensile strength, electrolyte corrosion resistance and heat sealing strength, proving to be excellent as a battery package material, a composite shell over lithium batteries for numerous electronic items. The soft pack battery is made of plain aluminum foil (8021 alloy 0.04mm thick), plastic film and special glue. The inner core is placed in the aluminum plastic film, which is used to make the battery of electronic products for daily use, so as to replace more lead-acid batteries. The flexible battery is packed with aluminum foil in structure. In case of hidden danger, the flexible battery w...

　　 1060 aluminum strip for transformer winding  contains more than 99.6% aluminum, also called pure aluminum strip. As a common grade in the aluminum strip family, 1060 strip has advantages of mature production technology, high plasticity as well as good corrosion resistance, conductivity and thermal conductivity. Because of its mature technology and simple process, its price is the lowest of various types of aluminum strips. 　　The alloy grades of commonly used aluminum strips are 1050, 1060, 1070, 1100, 3003, 3004, 5005, 5052, 8011, etc. The common states are o state and H state. O is the soft state and H is the hard state. O and h can be followed by numbers to indicate the degree of hardness and the degree of annealing. The thickness of  1060 aluminum strip  for dry-type transformers is between 0.08-3.00, made of 1060 high-quality pure aluminum, which has the characteristics of high conductivity, soft quality, smooth surface and no burr. It is an ideal material for ...

　　Top  1060 aluminum circle manufacturers  produce 0.5mm to 1.0mm thick aluminum round sheets for deep drawing and spinning. 1060 deep drawing wafers come into being after continuous punching of 1060 raw materials (mostly coil type). Such a process combines advantages of high efficiency, short cycle time and advanced automatic level, yielding superior circle discs with smooth clean surface and high cutting precision. Mould diameter of the punch line ranges between 100mm and 1250mm, which enables us to manufacture cold rolled and hot rolled aluminum circles for kinds of containers. Hot-rolled circles are highly tensile and anodizing friendly, mainly applied to aluminium kitchen utensils, cookware and containers. Our MOQ for 1060 hot rolled aluminium discs circles is 1 metric ton. 　　Traffic sign  1060 aluminum circle  stands out from our products, too. Developed primarily for traffic sign manufacturers, 1060 circle displays the best integrated performance at H14 st...

Aluminum coil 5182 5052 5754  is Al-Mg alloy of 0.1mm to 8mm thick. The magnesium of the coil usually ranges between 3% to 5%. Magnesium boasts an even lower density than aluminum, thus this alloy weighs less than other series of aluminium per square meter. Characterized by low density, high tensile strength, high elongation and good fatigue strength, this alloy can not be strengthened by heat treatment. Haomei 5000 series aluminum coils are among the more mature aluminum plate series, widely used in shipbuilding, construction, electronics and other conventional industries. 5182 aluminum coil  is high magnesium alloy with good strength, corrosion resistance and machinability. The anodized surface is beautiful. The arc welding performance is good. Due to its excellent corrosion resistance, 5083 alloy coil is widely used in marine applications such as ships, automobile, aircraft welding parts, metro light rail, pressure vessels (such as liquid tank cars, refrigerated vehi...

องค์ประกอบหลักของ  5052 อลูมิเนียมม้วน เป็นอลูมิเนียมและแมกนีเซียม แมกนีเซียมมีน้ำหนักเบากว่าอลูมิเนียมและมีความแข็งแรงดึงที่ดีและการนำความร้อน นอกจากนี้ยังมีจำนวนเล็กๆของแมงกานีสโครเมียมไนโอเบียมไทเทเนียมฯลฯ ส่วนใหญ่ของแมงกานีสในรูปแบบ mnal6 ยกเว้น ปริมาณขนาดเล็กของสารละลายของแข็ง ใน 5052 อลูมิเนียมอัลลอยโครเมียมทำหน้าที่คล้ายกับแมงกานีสมันช่วยเพิ่มความต้านทานการกัดกร่อนความเครียดแตกความสามารถของโลหะผสมอลูมิเนียมเพิ่มความแข็งแรงของวัสดุหลักและรอยเชื่อมและลดแนวโน้มของการแตกแต่เนื้อหาโดยทั่วไป ไม่เกิน 0.35 5052 อลูมิเนียมที่ใช้กันอย่างแพร่หลายมากที่สุดในความต้านทานการกัดกร่อน อลูมิเนียมม้วน กลิ้งอัลลอย ปริมาณแมกนีเซียมใน 5052 อลูมิเนียมม้วนอยู่ระหว่าง 2.2 ～ 2.8 เปอร์เซ็นต์หลังจากการรักษาความร้อนแมกนีเซียมต่ำไม่เสริมอลูมิเนียมอัลลอย มันมีความแข็งแรงปานกลางทนต่อการกัดกร่อนดี weldability ดีและง่ายต่อการประมวลผล 5052 อลูมิเนียมอัลลอยที่มีคุณสมบัติ พลาสติกที่ดีและอัตราการชุบแข็งสูงและพลาสติกแข็งต่ำ อุณหภูมิการตกผลึกของ 5052 อลูมิเนียมรีดร้อนประมาณ 288 อุณหภูมิอุณหภูมิเมื่ออัตราก...

Alloy: 5754 aluminum roll Material status: F, O, h111, H12, h14, H16, h18, H22, H24, H26, h28, H32, H34, H36, h38 Thickness (mm): 0.2-8 Width (mm): 100-2650 Length (mm): C Typical products: high-speed railway noise barrier, tank car tank material, high-grade alloy doors and windows, etc 5754 aluminum coil is a member of Al-Mg antirust aluminum, which has the characteristics of medium strength, good corrosion resistance, weldability and easy processing and forming. It is a typical alloy in Al Mg system alloy. Alloy 5754 aluminium with different heat treatment status is the main material used in automobile manufacturing industry (car doors, molds, sealing) and can making industry (tank body material). Aluminium 5754 grade material is widely used in welding structures, storage tanks, pressure vessels, ship structures and marine facilities, transportation tanks, as well as industrial products requiring excellent processing performance, excellent corrosion resistance, high fa...

Anodized aluminum sheet pantone  varies from supplier to supplier, but mostly consists of several color series: gray (including silver), red, blue, green, brown, red. Theoretically anodized aluminium sheets of each existing color can be made, which entails adjusting in coating process. The color of aluminum sheets by primary anodizing silver (the same as aluminum itself), and color anodizing is realized by coloring or electrophoresis (but the colors of which is less, generally champagne and gold). Anodizing films can be divided into: uncolored anodizing film (basically colorless and transparent anodizing film, i.e. no coloring treatment after anodizing), colored anodizing film (coloring treatment after anodizing), and dyed anodizing film (anodizing film that adsorbs the active color of dye in the pore structure and colors). Colors of anodized films are various, which is closely related to the alloy composition of the material, anodizing method and coloring or dyeing process....

　　 1060 aluminum circle for cooking utensils  can be of temper O, H12 or H14. Thickness ranges from 0.36mm to 5mm, and diameter from 120mm to 1000mm. The surface of the circle is usually mill finished, although color coating and anodizing can be customized according to per client’s practical needs. Mill finish 1060 circle discs are for ordinary cooking utensils made by processing steps of grinding, sandblasting and squeeze the lid. A pot comes into being in this way. Coated and anodized circles are processed into higher end cookware, such as pressure cookers, pizza baking pans, non-stick pan cake cookers and so on. 　　The specifications of our 1060 aluminum circles are complete. In addition to the conventional size, the disk with the thinnest 0.2 mm and the thickest thickness of 6.5 mm can be provided. The surface performance of the circle is so good that no obvious scratches, oil stains, oxidation or black spots appears on the surface. When the thickness of the circle is >0....

An  anodized brushed aluminum sheet  can be of alloys covering 1xxx to 7xxx series, including 1060, 1100, 1050, 1070, 2A12, 3003, 3004, 5052, 5A02, 5083, 5754, 6061, 6063, 6082 and 7075. Regular tempers include soft state(O, H111), hard state (H18, T6) and medium hard state (H24, H22, H32 and H112) to cater for requirements of varied clients. The sheet is from 0.007mm to 300mm thick (mostly below 10mm in practice), and 10mm to 2200mm wide (mostly 1000-2200mm). The production of anodized brushed aluminum sheets entail two extra processing steps in comparison to common mill finish aluminium sheets: brushing and anodizing. Brushing comes first, composed of three parts: degreasing, sanding, and washing. Then a brushed sheet gets anodized. The anodizing process is more complicated, consisting of on shelf, degreasing, washing, alkali corrosion, washing, neutralization, washing, anodizing, washing, hole sealing, washing, off shelf, detection and packaging. In the process, de...

Polish aluminum coil 3003  is of tempers O, H16, H14, H18 and H19. Its thickness ranges between 0.02mm and 3mm, and width from 100mm to 1600mm. 3003 aluminum alloy is an alloy in the wrought aluminum-manganese family (3000 or 3xxx series). Approximately 20% stronger than alloy 1100, it is readily formed by either conventional cold working or hot working. It can be cold worked (but not, unlike some other other types of aluminum alloys, heat-treated) to produce tempers with a higher strength, but a lower ductility. Haomei offers 3003 coil covered by the ISO standard 6361 and the ASTM standards B209, B210, B211, B221, B483, B491, and B547. Commonly used tempers include H14, H16 and H18 while others are also available by customers’ demands. The 3003-H14 is a softer, more formable aluminum coil. Polish  aluminum coil 3003  has very good corrosion resistance, moderate strength and excellent weldability, formability and machinability. It is commonly rolled and extruded, b...

　 3003 h26 aluminum coil  is a regular product of aluminum manganese alloy series, featured by good formability, solubility and corrosion resistance. It contains Silicon Si: 0.60, iron Fe: 0.70, copper Cu: 0.05-0.20, manganese Mn: 1.0-1.5, zinc Zn: 0.10, others: single 0.05 (total 0.15) and aluminum allowance. Due to the adding of manganese element, 3003 has excellent rust proof characteristics, also known as rust proof aluminum alloy. H26 refers to the temper of part annealing to 3 / 4 hard after work hardening, softer than H28 and harder than H24. 3003 H26 aluminum coil has a tensile strength (25 ° C MPa) of 170-210, yield strength (25 ° C MPa) 145, hardness 500kg force 10 mm 40, ball elongation 1.6mm (1 / 16in) 8-16 and thickness maximum shear stress MPa 95. 3003 aluminum coil has good corrosion resistance close to that of industrial pure aluminum. It has good corrosion resistance to atmosphere, fresh water, sea water, food, organic acid, gasoline, neutral inorganic salt ...

Black anodized aluminum sheets  are obtained by anodizing and coloring the surface of targeted aluminium sheets. Anodizing is a material protection technology for an aluminum plate to form oxide film on its surface by applying anode current in electrolyte solution. Cast aluminum can be black by common anodizing. After anodizing, the sheet is dyed with a black solution: acid MaoYuan att 20-30g / L acid lake blue 2-3g / L temperature 50-70 ℃ time 10-15min pH 3-3.5 (or 4.5-5.5). Film thickness can be made according to the requirements of customers, generally 10 to 20 microns. In comparison to original color anodizing, black anodizing takes an extra process and a longer time, thus it costs more. A black  anodized aluminum sheet  is widely used in mechanical parts, aircraft and automobile parts, precision instruments and radio equipment, building decoration, lighting, electronic products, handicrafts, home appliances, interior decoration, signs, furniture, automobile de...

　　 1050106010701100 aluminum circle sheet , falling on 1000 series, is between 0.1mm to 10mm thick. It incorporates all grades of the series: 1050, 1060, 1070 and 1100, which can be made into not only circle discs, but also sheets and coil rolls. As one of the most widely used aluminum alloy products, these circle sheets are widely used in electronics, daily chemicals, medicine, cookware, auto parts and other deep drawing or spinning products. Examples include non stick pots, pressure pots, lampshades, water heater shells, stretching tanks etc. 　　 1050 aluminum circle  contains Aluminum al: 99.50 silicon Si: < 0.25 copper Cu: < 0.05 magnesium mg: < 0.05 zinc Zn: < 0.05 manganese Mn: < 0.05 titanium Ti: < 0.03 vanadium V: < 0.05 iron Fe: 0.000 ~ 0.400 note: single ≤ 0.03. It’s stronger than either 1060 or 1070 discs, for it has less aluminium in the content. The chemical composition of 1060 is slightly different from that of 1050: Fe 0.35, Mn 0.03, Mg 0.03, ...

　　 12mciron thickness and 8011 alloy catering foil  is of 0.012mm thick, 8011 aluminium grade and usually O state. Other tempers include F, O, H14, H16, H18, H19, H22, H24, H26 and H28. The heaviest thickness of 8011 foil reaches 0.2mm, but thick foil rolls are usually made into food containers and sealing caps. Those used for catering is almost the thinnest of all, for softness and cleanness are more important than thickness here. 　　As a regular catering foil,  8011 aluminum foil  contains 0.05 to 0.90 share of silicon, 0.60 to 1.0 iron, 0.10 copper, 0.20 manganese, 0.05 magnesium, 0.05 chromium, 0.10 zinc and 0.08 titanium. It has a tensile strength between 125 to 165, yielding strength 110 and elongation 2 to 5. 8011 is made into aluminium foil because of its excellent properties. Cleaner than industrial pure aluminium of 1000 series, it shows better tensile strength as well. That’s why it can be made as thin as 9micron. Thin as it is, it does not breaks unless to...

Aluminium mirror sheet is a general term for reflective sheets or coils made of aluminium. Classified by reflectivity degree, mirror aluminum sheets falls on three types: 800 standard sheet, 850 superior sheet and 890 super sheet. Some of the sheets are polished, while some are anodized. There are two color series for the sheets: natural color and metal color. The former includes traditional red, orange, gold, light green, dark green, blue, light blue, purple, gray and black, and the latter comprises titanium gold, champagne, copper red, rose gold, light bronze, dark bronze and steel color. In some countries  rose gold aluminium mirror sheet s win tremendous popularity, and they are made into curtain walls, jewellery boxes, electronic shells etc. Rich colors of mirror sheets enables people to apply them in various surroundings. Take cell phone battery housings for example. Most cell phone manufacturers would highlight the color of a new product in their advertising. In China t...

5182 aluminum alloy sheet coil for marine and automobile uses can be of sheet or coil type. Specification of 5182 aluminum coil Thickness: 0.15mm-0.8mm Width: 20-2650 Temper: F, O, H12, H14, H16, H18, H19, H22, H24, H26, H28, H32, H34, H36, H38, H111, H112, H114, H116, H321 Application: car shells, oil tanks, electronic housing, pull rings 　5182 aluminum coil for bottle caps Thickness: 0.012-0.5mm Temper: H14, H16, H18, H19 Application fields: wine bottle caps, medicine bottle caps, cosmetics bottle caps, beverage aluminum bottle caps 　Specification of 5182 aluminum alloy sheet Thickness：0.8-600mm Width: 100-2650mm Temper: F, O, H12, H14, H16, H18, H19, H22, H24, H26, H28, H32, H34, H36, H38, H111, H112, H114, H116, H321 Length: 500-16000mm Application: Control panels, stiffeners, side and bottom outer plates, decks, refrigeration devices, tank cars, oxygen generator tower bodies, auto parts, etc 　　5182 aluminum plate for car doors Thickness: 0.15...

Thanks to fast development in science and technology, the  color mirror aluminum sheet  comes into being and brings more beauty to our world. This sheet is actually a type of anodized aluminum sheet that has been colored, for anodizing proves to be the best method for coloring a mirror sheet. Different from a regular piece of mirror sheet, anodized sheets have gone through an extra anodizing process. That’s how they obtain colors on the surface. Anodizing is one of the most frequently applied color coating process in aluminium processing industry, and its effect is more lasting and better than simple paint coating. A color  mirror aluminum sheet  is applied in electronic products, decoration and construction. Some time ago, a foreign school built a new teaching building whose curtain walls consist of pieces of color coated aluminium sheets and aluminum mirror sheets. The lower part of the building has seven colors and the upper part reflects trees of ...

7075 aluminum plate prices  are higher than prices of many other alloys because of its production entails advanced technology, and plate of different thicknesses have different prices, too. Generally the plate is between 1mm to 500mm thick, used in golf heads, shoe molds, high hardness molds, high-end mobile phone shells, thick plates, heavy forging, etc. Tempers plays a role in influencing the price, too. Regular tempers for the plate include O, T6, T651, T7451 and H112, among which T6 and T651 are the most frequently adopted. The tax inclusive price of the national standard 7075-T6 aluminum plate with thickness of more than 10 mm is about 33.8 yuan / kg, and the unit price of 7075-T651 aluminum plate is higher. The production cost of 7075 plates below 10 mm is higher, and the price will be higher. The cutting price for the plate is about 45 yuan / kg. The prices of 7075 plates are high for three reasons. First, the production cost is high. 7075 is a copper zinc aluminum all...

Aluminum alloy coil 1070 , from 0.1mm to 8mm thick, features high plasticity, strong corrosion resistance and good conductivity. Containing 99.7% aluminium, it’s usually made into structural parts with special properties, such as protective walls, wire cores, vent line parts, plan ornaments and so on. In addition to aluminium, 1070 aluminum coil consists of 0.04% copper, 0.03% magnesium, 0.04% zinc, 0.03% titanium and 0.05% vanadium. Tempers for  aluminum 1070 coil  is very broad, including F, O, H12, H14, H16, H18, H19, H22, H24, H26, H28, H111, H112 and H114. The width of the coil ranges between 20mm and 2650mm, and the length can be customized. Representative end products of the coil are radiators, charging piles, anti-corrosion insulation materials, wire, cable protection nets, aluminum buses, electronic products, oxide materials etc. What’s more, the coil can be made into foil type. Tempers are more or less the same. The biggest change lies in thickness. Foil thick...

A  non-stick aluminum circle/ aluminum disc  for pot can not be made of 1xxx aluminum. 3003 and 5052 would be a better choice. These are representatives of two levels of aluminum discs for non-stick cookers as well. 3003 aluminum circle  contains aluminium and manganese, known as a corrosion resistant circle alloy. It has excellent forming ability, high grain fineness and smooth surface. With a corrosion resistance is close to that of industrial pure aluminum, it has good corrosion resistance to atmosphere, fresh water, sea water, food, organic acid, gasoline, neutral inorganic salt solution, etc., and it also has good corrosion resistance in dilute acid. In spite of advantages above as a raw material for non-stick pots, the circle displays nonuniform color after being anodized, so anodizing is generally not carried out. In comparison, 5052  aluminum circle for cookwares  shows an excellent anodizing effect. Anodizing, however, does not make an aluminum d...

Haomei is among leading  aluminium slugs manufacturers .in our local market. Aluminum slugs, also known as aluminum shot and aluminum sand, are refined by repeatedly drawing, cutting, grinding and other processes of aluminum ingot containing 99% aluminum. With a bright and cylindrical appearance, they are applied to the surface of aluminum, zinc or thin-walled workpiece. In addition, they can be used in combination with stainless steel sand and stainless steel shot to achieve a whiter and brighter surface of the workpiece. Diameter: 2-13mm  Material: 1060, 1070  Main chemical composition: AI ≈ 99.5% Si < 0.2% CN < 0.04% Zn < 0.04%  Specific gravity: 2.7 g / cm3  Hardness: 65-125hv Specification: φ 1.0mm - φ 12mm  We provide  aluminium slugs .for steel making deoxidation. The chemical composition is in accordance with GB / t1196-2008, including aluminum ≥ al99.70%, specification: 2 ~ 13mm, and aluminum particles of different sp...

　　 Aluminium sheet for pp cap suppliers  is of 8011 h14, 8011h16 or 3003h16. The thickness is from 0.19mm to 0.23mm, and width 50-1000 up to your demand. Aluminium sheets are used for pp caps because of its advantages as below. 　　Stable Sealing Performance 　　The inner gasket of the aluminum anti-theft bottle caps is made of special sealing material, which has the characteristics of low permeability and zero permeability, and effectively prevents the oxidation of the wine in the bottle, keeping the wine fresh and fruity. No matter how long the storage time is, no chemicals will be produced within the bottle. 　　Environmental Friendly 　　The resources of bauxite are relatively rich. Aluminum anti-theft bottle caps can be recycled without environmental pollution. Haomei 8011 aluminum foil is of a level in brush water tests, boasting excellent moisture-proof performance, high shading and barrier capacity and safe application. 　　Convenient in Application 　　Aluminum anti-thef...

Mirror aluminum sheet 3003  ranks middle by quality in all alloys of aluminium mirror sheets. It overshadows 1050, 1060, 1070 and 1100 in either hardness or corrosion resistance, but can not compete with 5005, 5757, 5052 and 5083 in the two aspects. 3003 mirror sheets are used extensively in solar reflective panels, light reflective covers and ornaments, interior decoration, exterior decoration, home appliance panels, electronic product housing, kitchen furniture and decoration, automobile ornaments, logos, labels, jewellery cases and so on. 3003  aluminum mirror sheet  is a member of Al-Mn alloy, containing up to 1.5% manganese, 0.6% silicon, 0.2% copper, 0.10% zinc and 0.7% iron. The remaining part is aluminium. It has a tensile strength between 120 and 160Mpa, and a conditional yielding strength 85 and above. Haomei supplies 3003 mirror sheets of thickness from 0.1mm to 4mm and width up to 2200mm. Reflectivity ranges between 85% and 95%. The higher the reflectiv...

Aluminium coil alloy – 8011 /1060/1070  refers to three kinds of alloys by coil type: 8011, 1060 and 1070. They are between 0.09mm and 8mm thick, and 8011 is usually thinner than the other two, because it’s made into foil rolls for various packaging. Width and length can be customized. Regular thickness of 8011 aluminum coil ranges from 0.09mm to 0.2mm. The most popular temper is O. Although many other alloys fall on the scope of aluminum foil (like 1235, 1070, 1100, 1060, 3003, 8021, 8079 and 5052), 8011 is the only one covering all aspects in application, used in food packaging, pharmaceutical packaging, cosmetic packaging and kitchen cooking. To meet requirements of all these uses, 8011 aluminum foil has to be clean, healthy and smooth enough. Oil stains or heavy metals are not allowed. Both 1070 and  1060 aluminum coil  rolls belong to 1xxx pure industrial aluminum, featured by simple process, low hardness, good corrosion resistance and low price. 1060 contain...

1060 aluminum cookee circle is 0.01mm to 3mm thick and 100mm to 900mm round. Regular tempers include O, H18, H22 and H24.  1060 aluminum circle  is an industrial pure aluminum whose aluminum content (mass fraction) is 99.60%. The circle hardness can not be strengthened by heat treatment. The surface of pure aluminum is silvery white, and its density decreases with the increase of purity or temperature. Aluminum circle 1060 features relatively simple production, mature technology and much cheaper prices. With good elongation and tensile strength, it can fully meet the conventional processing requirements (stamping, stretching) with high forming ability. It has high plasticity, corrosion resistance, conductivity and thermal conductivity, but its strength is low. It can be welded by gas welding, hydrogen atom welding and contact welding, and it is not easy to be brazed, and it is easy to bear all kinds of pressure processing, drawing and bending, proving to be a good material f...

7075 aluminum plate suppliers  must have outstanding technique, process and equipment strength, for 7075 aluminum is a super hard aluminium which can not be produced by common hot rolling machines. 7075 aluminum sheet is a cold-treated forging alloy with high strength and hardness, far superior to mild steel. 7075 aluminium alloy is one of the most powerful commercial alloys, with common corrosion resistance, good mechanical properties and anode reaction. Fine grains make the deep drilling performance better and the tool wear resistance enhanced. Common tempers for 7075 plate include O, T6, T73, T76, T651, T7351 and T7651. The most popular ones are T6 and T651. T6 is for thin 7075 sheets, while T651 is for thicker ones. Thick  7075 aluminum plate  sheets are used for making aircraft structure and other high stress structural parts with high strength and strong corrosion resistance, such as upper and lower wing panels, purlins, partitions, etc. After solution treatme...